Відео

Hi mate thanks for the review, how do you change the blade, help plz am stuck😂

OK, fine, but what on earth is all this pounds, ounces and inches stuff? The blade is 185mm as in the model number 🙄

For me I feel theses things don’t hold up very well in a professional environment. Might be good for projects here and there but I work in an industry factory we deal with inks that when it dries turns to basically concrete. So sometimes we are using impact chisels for hours, I just don’t feel they hold up under very heavy use . The ones we had at work failed after 3 weeks, and the other 2 after a month. So consider that I own and use a snap on impact hammer which I bought years ago has held up under very heavy use where the sds failed but my air hammer keeps going I’ve used it so much where I broke 3 chisels and dulled several times others . Again this is my opinion but I do feel air tools are built way better.

You deserve some thanks for this. I'd love to ask you which bit of the valve fails most. The electric head (motor) or the valve seals?

If servicing means sending it off to Bosch, isn't it cheaper and easier to buy a replacement?

I've just been lent one of these by a neighbours. It doesn't detect water pipes (eg for use pins or hooks for hanging things up in kitchen)? I am concerned as a former neighbour caused a flood by making a mistake. I am a complete novice.

Very helpful, thank you!

I've had mine 2 years. It does studs too

Hi there just watched the video , i have one of theses ,now when we flush it it fills up ok but abit to much as it goes down the over flow and believe it or not it run our of the screw hole i think as it dripping on the floor , is there a wat to adjust the flow of water , cheers nige

Fantastic. Thank you... .

Great short video mate, i seen so many so-called plumbers get this so so wrong.

I have always used a thinner piece of wood behind it and it works much better. Using a thicker piece of wood never works for me. Either is better than just duck tape though.

Many thanks for this. There is a mass of unhelpful information available on the internet; this actually told me what I needed to know.

Clear concise and to the point. Cheers.

If you're promoting this product, it might be prudent to point out some of the pitfalls. For instance, if your property has imperial / old copper piping, the standard Aladdin unit is no use because the teeth in the standard gadget are not strong enough to cut all the way tough the thicker walls of the piping. In fact, it can be disastrous to try the standard unit in older properties. There is little or no guidance on this unless you have issues and then look at Aladdin's Troubleshooting pages where it is mentioned. So, if you're suggesting that all plumbers carry one in their kit, you maybe should advise them to carry one of each, standard and Pro, of the 15mm size.

Thank you so much, you saved my life!

Cheers for the video. Took about 5 tries and was about to give up. Not sure if it was the cursing or the threat of driving it straight up to the scrapyard, but it eventually worked!

oh yeah! Thank you from Spain, the trick works for my standers padlock!

I did your method for my project and worked well

Super helpful, thank you

Yeah ive got this as my cheap and light 5.5mm fixings drill and chiselling 👍🏻 its perfect. My dch334 is my heavy duty drilling option

This guy barked for a full minute before he actually did anything. Quick video my a___s

Is your thumb ok

Excellent Dan. It put me on the right road to finish the job!

Just bought a used one but noticed the front handle is missing. I've ordered another but do you think it can be used in the meantime without the side handle?

RPM?

Es una sierra para recomendar 10/10. Suave para cortar Suerna pero tan duro motor agradable La sierra entra facil en la madera Corte fino Corte preciso Y la bolsa como todas las sierras son obsoletas. Buenos materiales Muy liviana fácil de cargar y ligera.

Cheers fella , decent watch that was , easy to follow.

Hiya, this worked for me too. Thank you so much 👍🥳x

I opened mine and water came out of it is the pump gone

Thanks a million! Old bath star tap would not unscrew to get to the washer, no wire brush I used a junior hacksaw carefully to remove dirt on top of thread. Then for leverage I used large adjustable spanner and to stop tap moving (as pipes all soldered here years ago and that would be a disaster) the end of mole grips with the adjustable nurled bit at the end made it as long as possible whilst still a half inch within the grip and put it into the tap water outlet as far as possible and the leverage made the tap undo really easy! LEVERAGE is what we need as you say! New washer on (and that was a bas----- to get over the spigot! Thanks, Mike. Thanks,

I tired the 3rd method and it worked a treat - thank you for sharing your tip - really helpful 😊

Legend

Someone stole my porridge.

👍👍👍👍 Not up to veto standard for the price

The whole I watched the video was to see how the rubber seals go on the pan .You didn't show idiot

Tried several times and won’t work. Then I realized I wasn’t releasing my foot off the brake pedal fully during the x2 counts. Literally had to press all the way down and release fully off the brake pedal x2 then hold on the 3rd. Boom 💥 it worked 😅

SlurryDestroyer. Non corrosive and safe. Softens concrete for easy cleaning.

First time ising and cannot seem to unlock it, used it a few times. Its not blocked but cant seem to get it to work again

Thanks man

Great job 👏

Great video and great demonstration

what's put me off, is you are being forced to send it off to get it serviced , and all they will do is reset it and charge you , What a load of rubbish , Its all electronic what can go wrong

Is it possibel to just change the putside mirror cover?

how this flush valve works? by air or pumping fluid?

When I used a brick mason recently, he chipped them in his two hands. He held the brick with one hand and smacked it with a chipping hammer one time with the other. One smack and done. I didn’t see him have to toss any mistakes. I wish I had paid more attention now that I need some pieces for a project.

💯🙋‍♂️💪 thanks brother 🤝

saved my day, thx!

brilliant thanks

Thank you